|
On this page you can post your question and after review it may be approved and a response may be written by the Lamkin Expert.
The following questions have been asked and answered:
|
|
Asked by todd mccurry on May 5, 2010 at 1:31 pm
Q: what is the difference in using tape with a standard grip vs using a midside grip initally to obtain a midsize?? firmer? shorter life,etc...???
A: If too much tape is used or if the tape is not applied evenly, the grip may become stretched and suffer premature wear.
Best regards,
Lamkin Sales Team
Asked by kevin d on April 28, 2010 at 10:06 am
Q: do you sell any undersize grips in your performance models>
A: Currently we do not offer an undersize model in our Performance Plus or Performance Plus 3GEN models. We are currently working on new models for 2011 - check back later this fall to see if we add one.
We do offer an undersize model in our Crossline series.
Best regards,
Lamkin Sales Team
Asked by David on April 26, 2010 at 7:47 am
Q: Your Perma Wrap packaging says to NOT use soap and water to clean them. Other than water- what can/should I use?
A: Lamkin's full line of synthetic rubber grips can be cleaned using soap and water or simply water using a wet towel. The exceptions to the rule are the non-rubber models (Comfort Wrap, Seamless Polyurethane Putters and 2TEN putters). These should be cleaned with water and a non-aggressive towel to protect from roughing up the polyurethane surface of the grip.
Best regards,
Lamkin Sales Team
Asked by LEO on April 21, 2010 at 10:04 am
Q: ALL 13 CLUBS IN MY BAG ARE .600 BUTT, I WANT TO PUT ON CROSSLINE MIDSIZE GRIPS BUT THEY ONLY COME IN .580 CORE WON\\\'T THIS MAKE GRIP WHEN INSTALLED LARGER THAN MIDSIZE?
A: Using a .580\" core grip on a .600\" butt shaft will produce an installed grip size of 1/64\" oversize. Midsize grips are generally 1/16\" oversize.
For peak performance, we recommend that all golfers be fit for grips by a PGA professional or a professional clubmaker.
Asked by chris on April 18, 2010 at 10:43 am
Q: what is the easiest way to properly replace a ribbed grip so that it is on correctly (or square to the club face)?
A: The easiest way is to make sure that the tic marks located near the trim rings on the butt and mouth ends of the grip are properly aligned. This will ensure that the grip is on straight and the rib (or reminder) is installed straight also.
Best regards,
Lamkin Sales Team
Asked by Jim Schmitz on April 12, 2010 at 2:27 pm
Q: I\'m 74 and never looked at a grip sizing chart. I havr used jumbo grip\'s all my life and find that \"Standard\" is the correct size. What are the consequenses of using too large a grip???
A: Using a grip that is too large may cause you to leave the clubface open, thus resulting in a shot to the right.
Best regards,
Lamkin Sales Team
Asked by Scott on April 12, 2010 at 5:36 am
Q: It seems as though all of todays \"ribbed\" grips have less of a reminder than previous year\'s models. Is this true and is there any reason for it?
A: At Lamkin, we have not changed the specifications of the rib (or reminder) in our grips.
Best regards,
Lamkin Sales Team
Asked by Steve on April 11, 2010 at 8:05 pm
Q: Hey, I am looking at the new n-dur 3GEN grips but realize they only come in standard size. I was wondering how many wraps I could add to try and make these close to a midsize.
A: For most shaft diameters, we would recommended an additional two layers of tape. We would recommend that you visit a retail store or pro shop that specializes in regripping so that you can be properly fitted for your grips.
Regards,
Lamkin Sales Team
Asked by Mike S. from Wauconda, IL on April 8, 2010 at 1:58 pm
Q: I currently have the green, dual density oversized grips on my club and I would like to regrip with a simular grip in one of your current styles. I need to stay with an oversized grip. I wear an XL golf glove. Can you make a recommendation?
A: Performance Plus Midsize with 3GEN material would be an excellent replacement choice. The 3GEN material is extremely tacky, yet durable.
Regards,
Lamkin Sales Team
Asked by Don on April 4, 2010 at 8:13 am
Q: I would love to try your new N-DUR grips but I require a midsize grip. I can\'t find this grip in a midsize. Do you make this grip in midsize?
A: Thank you for your interest. Currently we do not offer N-DUR in a midsize version. We are constantly developing new models, so this one may be available in the future.
The current N-DUR model can be made larger by using build-up tape. Several of our distributors offer tape to do this. Please feel free to contact them.
Regards,
Lamkin Sales Team
Ask your Question:
|
